Beschrijving
Membraanpomp met hoge zuivering
De eenvoudige demontage van de vloeistofuiteinden, grote draagbaarheid en hoge stroomcapaciteit maken van de SaniForce 3150 HS-pomp een perfecte oplossing voor al uw toepassingen met hoog volume. Ontworpen voor toepassingen die gebruikmaken van het ontwerp met snelle assemblage, maar waarvoor mogelijk geen lekdetectie nodig is.
Eigenschappen van de Graco SaniForce 3150HS serie:
- tilt
- Laat vaste stoffen met een diameter tot 25 mm (1 inch) door
- Kan eenvoudig omgevormd worden tot een 3150 sanitaire flappomp met de optionele set
- Vochtige of met vloeistof gevulde centrale secties van roestvrij staal
- Met het duurzame niet-klevende luchtventiel zonder smeermiddel van Graco
Wij van HSC Pumps gaan graag met u in gesprek of geven u geheel vrijblijvend een demo. Neem contact met ons op en bespreek de mogelijkheden:
Contact opnemenSaniForce 1590 HS and 1590 3A Diaphragm Pumps | |
Maximum fluid working pressure |
8 bar, 0.8 MPa
|
Air pressure operating range |
1.4–8 bar, 0.14–0.8 MPa
|
Maximum air consumption |
3.5 m³/minute
|
Air consumption at 70 psi, 60 gpm |
1.4 m³/minute
|
Maximum free-flow delivery |
378 lpm
|
Maximum pump speed |
200 cpm
|
Gallons/liters per cycle* |
2.0 l
|
Maximum suction lift (varies widely based on ball/seat selection and wear, operating speed, material properties, and other variables) |
8.5 m wet, 4.6 m dry
|
Maximum size pumpable solids |
15.9 mm
|
Air inlet size |
0.5 in npt(f)
|
Noise Data** | |
Maximum Noise Level at 100 psi (7 bar, 0.7 MPa), full flow |
90 dB(A)
|
Sound power level |
103 dB(A)
|
Noise level at 70 psi (4.8 bar, 0.48 MPa), 50 cpm |
85dB(A)
|
Maximum fluid operating temperature is based on the following maximum diaphragm, ball, and o-ring temperature ratings | |
PTFE |
104°C
|
Santoprene® |
82°C
|
3A Approved EPDM |
135°C
|
Wetted Parts*** | |
All fluid contact materials are FDA-compliant and meet the United States Code of Federal Regulations (CFR) Title 21, Section 177. | |
Wetted materials on all models |
316 stainless steel, 3A Approved EPDM, PTFE
|
Wetted materials depending on model |
3A Approved EPDM, PTFE, Santoprene
|
CAUTION: Santoprene may be used only with non-fatty, non-oily foods or alcohols up to 15% | |
Non-wetted external parts |
300 series stainless steel, polyester (labels), LDPE foam (gasket)
|
Weight | |
All Models |
44 kg
|
Santoprene® is a registered trademark of the Monsanto Co. Loctite® is a registered trademark of the Loctite Corporation. * Displacement per cycle may vary based on suction condition, discharge head, air pressure, and fluid type. ** Noise levels measured with the pump mounted to a solid surface. Sound power measured per ISO Standard 9614–1. *** The pump user must verify that the construction materials meet their specific application requirements. |